Search Results

The Association des Constructeurs Européen d'Automobiles (ACEA) light duty diesel engine specifications requires a kinematic viscosity measurement technique for Peugeot XUD-11 BTE drain oils. This viscosity measurement is used to define the medium temperature dispersivity of soot in the drain oil.(1) This paper discusses the use of rotational rheology methods to measure the Newtonian character of XUD-11 drain oils. The calculation of the rate index using the Hershel Bulkley model indicates the level of non-Newtonian behavior of the drain oil and directly reflects the level of soot dispersion or agglomeration. This study shows that the more non-Newtonian the drain oil the greater the difference between kinematic and rotational viscosity measurements Oscillation (dynamic) rheological techniques are used to characterize build up of soot structure.

One of the key functions of lubricating oil additives in diesel engines is to control oil thickening caused by soot accumulation. Over the last several years, it has become apparent that the composition of the base oil used within the lubricant plays an extremely important role in the oil thickening phenomenon. In particular, oil thickening observed in the Mack T-8 test is significantly affected by the aromatic content of the base oil. We have found that the Mack T-8 thickening phenomenon is associated with high electrical activity, i.e., engine drain oils which exhibit high levels of viscosity increase show significantly higher conductivities. These findings suggest that electrical interactions are involved in soot-induced oil thickening.

Liquid spray applied damping materials have potential advantages over conventional sheet damping materials in automotive body panel vibration applications. In order to understand the acoustical impact, a laboratory based NVH study was conducted to compare the damping and stiffness performance characteristics of various sprayable damping materials versus the production damping treatment. Based on this comparison, a criteria was developed to select potentially viable sprayable damping materials for vehicle testing. In-vehicle tests were also performed and compared to the laboratory findings to understand how well the results correlate. This paper discusses a criteria for selecting sprayable damping materials based on bench-top tests for vehicle applications, and the potential benefits of sprayable materials.

A student team from Brigham Young University (BYU) set a new record for the world's fastest electric drag racecar. The team modified a production EV1 donated to the university by the General Motors Corporation and installed a bank of 160 UltraCapacitors rated at 2700 farads each. This paper describes the design of the capacitor pack, the car's drive train, the charging method and other modifications of the vehicle. Here we also discuss performance and race data from an official quarter-mile drag race sanctioned by the National Electric Drag Racing Association. A simulation model for vehicle performance was also developed and is presented here.

A traction test machine, developed for evaluation of traction-CVT fluids for the automotive consortium, USCAR, provides precision traction measurements to stresses up to 4 GPa. The high stress machine, WAMhs, provides an elliptical contact between AISI 52100 steel roller and disc specimens. Machine stiffness and positioning technology offer precision control of linear slip, sideslip and spin. A USCAR traction test methodology includes entrainment velocities from 2 to 10 m/sec and temperatures from -20°C to 140°C. The purpose of the USCAR machine and test methodology is to encourage traction fluid development and to establish a common testing approach for fluid qualification. The machine utilizes custom software, which provides flexibility to conduct comprehensive traction fluid evaluations.

A turbocharged version of the 2.4L engine has been developed by the Chrysler Group of DaimlerChrysler Corporation. This new engine is derived from the proven 2.4L 4-cylinder, with significant changes to achieve a durable, high performance package for the PT Cruiser vehicle. The package includes an integrated turbocharger / exhaust manifold, oil squirters for piston cooling, and numerous other upgrades to satisfy the demanding performance, emissions, and durability requirements unique to this powertrain. The purpose of this paper is to describe the mechanical changes to the base engine, the unique turbocharger configuration, and the new parts necessary to accommodate the higher output.

Accurate motion prediction can be used to evaluate vibrations at seat track and steering wheel. This paper presents the prediction and correlation of truck frame motion from wheel force transducer (WFT) measurements. It is assumed that the method can be used to predict vibrations at seat track and steering wheel for unibody vehicles. Two durability events were used for calculation. WFT measurements were used as inputs applied on frame from suspension. Frame loads were then used as inputs to calculate frame motions using a FEA approach. The predicted frame motions are represented by four exhaust hangers and they are compared with measured motions of the same locations. The correlations include displacement, velocity, and acceleration. It is shown that good correlations are obtained in velocity and displacement. Acceleration shows bigger differences than velocity and displacement.

This paper introduces a reliable method to calculate body mount loads from wheel-force-transducer (WFT) measurements on framed vehicles. The method would significantly reduce time and cost in vehicle development process. The prediction method includes two parts: Hybrid Load Analysis (HLA) that has been used by DaimlerChrysler Corporation and Body Mount Load Analysis (BMLA) that is introduced by this paper for the first time. The method is validated on a body-on-frame SUV and a pickup truck through one proving ground events. The example shown in this paper is for a SUV and one of the most severe events. In HLA, the loads at suspension-to-frame attachments are calculated from spindle loads measured by WFT. In BMLA, body mount loads were calculated using outputs of HLA with detailed finite-element-modeled frame and body. The loads are compared with measured body mount loads. The comparisons are conducted in range, standard deviation (S.D.), and fatigue pseudo-damage.

A premixed compression-ignited (PCI) combustion system, which realizes lean combustion with high efficiency and low emissions, was investigated and its effects and problems were ascertained. With PCI combustion, fuel was injected early on the compression stroke and a premixed lean mixture was formed over a long mixing period. The test engine was operated with self-ignition of this premixed lean mixture. From the results of combustion observation and numerical simulation, a need to prevent the fuel spray from adhering to the cylinder liner and combustion-chamber wall was identified. Consequently, an impinged-spray nozzle with low penetration was made and tested. As a result, an extremely low nitrogen-oxide (NOx) emission level was realized but fuel efficiency was detracted slightly. Also, the engine operating range possible with PCI combustion was found to be limited to partial-load conditions and PCI combustion was found to cause an increase in hydrocarbon (HC) emission.

Transmission mounts are usually tested as an assembly and typically only translational stiffnesses are provided. The torsional stiffness of the assembly is traditionally estimated based on experience in load simulation and analysis. This paper presents a procedure to estimate the torsional stiffness of the transmission mount assembly by using the test data. The effects of the torsional stiffness on the simulation results are also discussed.

NASA's plans to implement the Vision for Space Exploration include extensive human-robot cooperation across an enterprise spanning multiple missions, systems, and decades. To make this practical, strong enterprise-level interface standards (data, power, communication, interaction, autonomy, and physical) will be required early in the systems and technology development cycle. Such standards should affect both the engineer and operator roles that humans adopt in their interactions with robots. For the engineer role, standards will result in reduced development lead-times, lower cost, and greater efficiency in deploying such systems. For the operator role, standards will result in common autonomy and interaction modes that reduce operator training, minimize workload, and apply to many different robotic platforms. Reduced quantities of spare hardware could also be a benefit of standardization.

Tip-in/Tip-out of the accelerator pedal generates transient torque oscillations in the driveline. These oscillations may be amplified by P/T, suspension and body modes and will eventually be sensible at the receiver side in the vehicle, for example at the seat or at the steering-wheel. The forces that are active during this transient excitation are influenced by non-linear effects in both the suspension and the power train mounts. In order to understand the contribution of each of these forces to the total interior target response (e.g. seat rail vibration) a detailed investigation is performed. Traditional force identification methods are not suitable for low-frequent, transient phenomena like tip-in/tip-out. Mount stiffness method can not be used because of non-linear effects in the P/T and suspension mounts. Application of matrix inversion method based on trimmed body vibration transfer functions is not possible due to numerical condition problems.

It is often necessary to measure three-axis displacement of a deforming or moving part in static or dynamic impact tests. A point moving in the three-dimensional space can be monitored and measured using three string-pots or other distance measuring devices with a methodology developed here. A numerical algorithm along with required equations are shown and discussed. The algorithm was applied as an example to static seat pull test and compared to results from film analysis. The application with string pots is useful especially when the point of concern gets hidden or blocked by other parts disabling the photogrammetry technology.

Crankshafts must be balanced statically and dynamically before being put into service. However, without pistons and connecting-rod assemblies, a non-symmetric crankshaft is not in dynamic balance. Therefore, it is necessary to apply equivalent ring-weights on each of the crankpins of the crankshaft when balancing it on a dynamic balancing machine. The value of the ring weight must be accurately determined, otherwise all advantages that are derived from balancing would be of no avail. This paper analytically examines the theoretical background of this problem. Formulas for calculating the ring weights are derived and presented. These formulas are applicable to a generic class of crankshafts of V-type engines with piston pin offset. Also, practical consideration, such as the design and manufacturing of these ring weights, the method of testing, and correction is addressed.

Knock noise induced by automotive shock absorbers has serious influence on driving comfort and vehicle quality. Some research focusing on knock noise had been introduced in the past. However there is the unidentified phenomenon that has been unnoticed. This paper describes the new theory to clarify one of the unidentified phenomenon and proposes the equation for stability assessment which is useful on designing stage of development. First of all, the characteristics of the unidentified rod vibration of shock absorbers are investigated experimentally. Second, the new theory is established on the basis of the non-linear physical model with friction forces between piston and cylinder. This theory shows that the unstable vibration, so called the Self Excited Vibration, can be induced by not only friction property but also structure of rod and piston. Third, the equation for stability assessment, which is useful on designing stage of development, is proposed on the basis of new theory.

In API engine oil licensing, a candidate oil must meet the performance requirements of category defined engine tests. The reason for the engine tests is to assess the capability of the candidate oil in field performance. Unfortunately, due to the time consuming and expensive nature of most engine tests, a candidate oil is typically run only once or twice in an attempt to meet the performance requirements. Given that the results from most engine tests have large amounts of variability, the assessment of the candidate oil in several tests, although adequate, is obviously not perfect or inexpensive. The Virtual Engine Test is a process in which the time and expense of category defined engine tests may be reduced while maintaining, or even improving, the assessment of the candidate oil capability.

Life Cycle Assessment (LCA) is a methodology used to determine quantitatively the environmental impacts of a range of options. The environmental community has used LCA to study all of the impacts of a product over its life cycle. This analysis can help to prevent instances where a greater degree of environmental harm results when changes are made to products based on consideration of impacts in only part of the life cycle. This study applies the methodology to engine lubricants, and in particular chlorine limits in engine lubricant specifications. Concern that chlorine in lubricants might contribute to emissions from vehicle exhausts of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), collectively called PCDD/F, led to the introduction of chlorine limits in lubricant specifications. No direct evidence was available linking chlorine in lubricants to PCDD/F formation, but precautionary principles were used to set lubricant chlorine limits.

Over the past five years, the US Automotive Materials Partnership (USAMP) has brought together representatives from DaimlerChrysler, General Motors, Ford Motor Company and over 40 other participant companies from the Mg casting industry to create and test a low-cost, Mg-alloy engine that would achieve a 15 - 20 % Mg component weight savings with no compromise in performance or durability. The block, oil pan, and front cover were redesigned to take advantage of the properties of both high-pressure die cast (HPDC) and sand cast Mg creep- resistant alloys. This paper describes the alloy selection process and the casting and testing of these new Mg-variant components. This paper will also examine the lessons learned and implications of this pre-competitive technology for future applications.

The objective of this paper is to present one of the application of the finite element method (FEM) in early stages of vehicle development to calculate larger deflections of body sheet panel. The stiffness of sheet metal shells is defined in conjunction with the local elastic buckling instability under concentrated loads. Considerable amount of weight reduction of outer panels could be obtained by optimizing metal gauges, radii, peripheral conditions and reinforcing manner of the panel. Among several outer panels of an automobile, a roof panel is picked up as an example and its stiffness is calculated by FEM analysis. The results shows satisfactory coincidence with the experimental ones. Regarding the calculation procedure, Central Processor Unit (CPU) time of finite elements was found to be reduced by varying and optimizing supporting conditions of the panel. Furthermore, the stiffness analysis program during the initial design stages of vehicle development is described.

The Engine Oil Industry Base Oil Interchange (BOI) and Viscosity Grade Read Across (VGRA) guidelines developed by the American Petroleum Institute (API) provide a means to significantly reduce the time to market for current technology engine oils. This process has several advantages including the public display of data and a consensus evaluation of the submitted data. The process also has several limitations including timeliness of the consensus process, and the applicability and flexibility of an all-encompassing, industry-wide guideline. An enhancement to the all-encompassing, industry-wide consensus process is the Single Technology Matrix (STM). The idea behind this approach is to use sufficient data from a single technology to develop and use BOI for that specific technology. The advantages of the STM include improved technical merit, timeliness and flexibility in establishing BOI.